OWON HDS2062M-N — 60 MHz 2-Channel Handheld Oscilloscope + 1000 V Multimeter
OWON HDS2062M-N handheld oscilloscope: 60 MHz, 2 channels, 1 GS/s, with a 4000-count 1000 V multimeter, 3.7″ VGA screen, FFT, auto-scale and 6-hour battery.
A 2-channel scope and a 1000 V multimeter, in one hand
The OWON HDS2062M-N is the 60 MHz model of OWON’s HDS-N handheld range: a 2-channel, 60 MHz digital storage oscilloscope sampling at 1 GS/s and a 3¾-digit (4000-count) multimeter in one rubber-armoured housing, with an FFT spectrum view on top. The multimeter has its own input jacks and measures up to 1000 V DC, 750 V AC and 10 A.
A 3.7-inch, 640 × 480 colour screen, auto-scale, 20 automatic measurements and edge, video and alternate triggering cover everyday service work. The 7.4 V Li-ion battery runs it for about six hours, and USB takes waveforms and meter readings to a PC.
Why the HDS2062M-N
Two instruments you would otherwise carry separately, with the controls that make a handheld quick to use.
Oscilloscope + 4000-count meter
Switch from a two-channel waveform view to a 3¾-digit multimeter with its own 10 A, mA, COM and V/Ω/C jacks: voltage to 1000 V DC / 750 V AC, current to 10 A, resistance to 40 MΩ, capacitance, diode and continuity.
Click to enlarge
One-key auto-scale
Press Autoscale and the scope sets trigger, vertical scale and timebase from the type, amplitude and frequency of the input. Two channels are measured on screen straight away — useful when you do not know what is on the pin yet.
Click to enlarge
Edge, video & alternate trigger
Alternate trigger holds two unrelated signals stable at the same time, each on its own trigger. Adjustable trigger sensitivity rejects noise, so a waveform that jitters on screen locks on.
Click to enlarge
6-hour Li-ion battery
A 7.4 V, 3500 mAh rechargeable Li-ion pack gives about six hours of use away from mains; the supplied adapter runs it from 100–240 V AC. Weight 645 g, 115 × 180 × 40 mm.
Internal lithium-ion power and a rugged case, so the instrument works away from a bench and a mains socket.
The measurement often has to happen where the problem is — up a mast, in a plant room, in a vehicle. An instrument that has to be carried to the fault and run for a few hours changes what can be diagnosed on the day.
In practice: Tracing interference across a site on foot, taking readings at each location without hunting for power.
Who it’s for & best applications
With 60 MHz on two channels and a 1000 V meter in the same housing, the HDS2062M-N is made for service and repair work up to a few tens of megahertz — switching edges, serial lines and microcontroller clocks included: power electronics, audio, sensors, motor drives and vehicle systems.
- Field-service and maintenance technicians
- Automotive maintenance and testing
- Electronics repair benches
- Design and manufacturing test
- Education and training
- Electronic circuit debugging and circuit testing
- Power-supply, audio and sensor signals up to 60 MHz
- Mains-side voltage and current checks with the built-in meter
- Comparing two signals side by side with alternate trigger
- Spotting interference and harmonics with FFT
HDS2062M-N specifications
From the official OWON HDS-N series specification sheet. Bandwidth, sample rate, timebase, rise time and input capacitance are specific to the HDS2062M-N; the rest is shared across the series.
| Oscilloscope | |
| Bandwidth | 60 MHz |
| Channels | 2 |
| Real-time sample rate | 1 GS/s |
| Rise time (at input, typical) | ≤ 5.8 ns |
| Timebase | 5 ns/div – 100 s/div, 1-2-5 steps |
| Record length | 6K points |
| Vertical sensitivity | 5 mV/div – 5 V/div (at input) |
| Vertical resolution | 8-bit |
| Input coupling | DC, AC, GND |
| Input impedance | 1 MΩ ±2%, in parallel with 15 pF ±5 pF |
| Max input voltage | 400 V (DC + AC peak-to-peak, 1 MΩ, 10:1 probe), CAT II |
| Probe attenuation | 1X, 10X, 100X, 1000X |
| DC gain accuracy | ±3% |
| DC accuracy (average) | Average > 16: ±(5% of reading + 0.05 div) for ΔV |
| Interpolation | sin(x)/x |
| Trigger, measurement & analysis | |
| Trigger types | Edge, video, alternate |
| Trigger modes | Auto, normal, single |
| Trigger level | ±6 divisions from screen centre |
| Acquisition modes | Sample, peak detect, average |
| Automatic measurements | 20 — Vpp, Vavg, Vrms, frequency, period, Vmax, Vmin, Vtop, Vbase, Vamp, overshoot, preshoot, rise time, fall time, +width, −width, +duty, −duty, delay A→B rising and falling |
| Waveform math | +, −, ×, ÷, invert, FFT |
| Waveform storage | 4 waveforms |
| Lissajous (X-Y) | Full bandwidth · phase difference ±3° |
| Multimeter | |
| Display | 3¾ digits (max 4000 counts) |
| Input impedance | 10 MΩ |
| DC voltage | 400 mV, 4 V, 40 V, 400 V, 1000 V · ±(1% + 1 digit) · max 1000 V DC |
| AC voltage | 4 V, 40 V, 400 V ±(1% + 3 digits) · 750 V ±(2% + 3 digits) · 40–400 Hz · max 750 V AC rms |
| DC current | 40 mA, 400 mA ±(1.5% + 1 digit) · 10 A ±(3% + 3 digits) |
| AC current | 40 mA ±(1.5% + 3 digits) · 400 mA ±(2% + 1 digit) · 10 A ±(5% + 3 digits) |
| Resistance | 400 Ω ±(1% + 3 digits) · 40 kΩ – 4 MΩ ±(1% + 1 digit) · 40 MΩ ±(1.5% + 3 digits) |
| Capacitance | 51.2 nF – 100 µF ±(3% + 3 digits) |
| Diode | 0 – 1.5 V |
| Continuity | Beeps below 50 Ω (±30 Ω) |
| Remote | SCPI over USB (multimeter) |
| Display, power & general | |
| Display | 3.7-inch colour TFT, 640 × 480 pixels |
| Interface | USB (PC software, waveform and data transfer) |
| Battery | 7.4 V Li-ion, 3500 mAh · approx. 6 hours’ operation |
| Mains adapter | 100 – 240 V AC, 50/60 Hz |
| Power consumption | < 6 W |
| Dimensions (W × H × D) | 115 × 180 × 40 mm |
| Weight | 645 g (without packaging) |
Subject to change, errors & omissions excepted.
In the box
The HDS2062M-N ships ready to measure — probes for the scope, leads for the meter, and the adapter to charge it.
The soft bag is an option. Contents as listed by OWON, subject to final delivery. The PC software is also a free download — see Downloads below.
Other models in the HDS-N series
All four HDS-N models share the 3.7-inch VGA screen, the 4000-count 1000 V multimeter, the 6K record and the 6-hour battery. Bandwidth and sample rate are what change: the HDS1022M-N samples at 100 MS/s, the 60, 100 and 200 MHz models at 1 GS/s.
Newer OWON handhelds
If you do not need the 1000 V DC meter range or the larger VGA screen, OWON’s newer pocket-size platforms add a waveform generator and a higher-count meter.
Questions about the HDS2062M-N?
Tell us the signals and voltages you work with and we’ll confirm the HDS2062M-N is the right pick, or point you to a better fit in the OWON handheld range.
Downloads
Official OWON documentation and software for the HDS2062M-N (HDS-N series, 2-channel).
See also the OWON factory product page.